Manufacturer:
Type:
Protocoll:
Devicename:
Model_nr:
Version_nr:
Version_info:
Version_timestamp
Release:
ID
Min_mygekko_version:
Function_type:
Progress_state:

Description (HTML)

<p>Integrate up to 32 Daikin Devices.</p>
<p><strong>Device Station Settings</strong></p>
<p>Enter the <strong>Slave IDs</strong> in the Slaves field, separated by a comma.</p>
<p>Example: 1,2,3,4,...</p>
<p><strong>Function Description</strong></p>
<p>Daikin fan coil units operate as Modbus slaves, while the controller operates as the Modbus master. By default, the controller regulates the room temperature by sending the fan speed and On/Off mode to the individual fan coil units.</p>
<p>The user can set the desired temperature thresholds directly in the <strong>Room Control</strong> system. Heating and cooling operation can be switched using configurable actions/timers.</p>
<p>The Daikin modes <strong>Auto</strong>, <strong>Fan</strong> and <strong>Dehumidification</strong> cannot be controlled.</p>
<p><strong>Note</strong></p>
<p>The remote control can be used when individual rooms have been switched off, so that the controller does not send any fan speed changes to the fan coil units.</p>
<p><strong>Connection</strong></p>
<p>The real-time converter is installed in each fan coil unit and connected to the RS485 bus using 3 wires (A/B/GND). (e.g. FTDI: A&minus; = yellow, B+ = orange).</p>
<p>To enable Modbus on the converter, simply set an address &gt;= 1 using DIPS 3 to 8. The first 2 DIPs can remain disabled unless you want to use a Modbus timeout to enable local operation. In this case, the corresponding registers must be written.</p>
<p>The fan coil units are also connected separately to the outdoor unit. Heating operation is only possible below the standard outdoor temperature of 18 &deg;C.</p>
<p>Create one <strong>Room Control</strong> element for each fan coil unit.</p>
<p><strong>Room Control&nbsp;IO Configuration &ndash; Sensors:</strong></p>
<ul>
<li><strong>Temperature:</strong> Specify the temperature sensor.</li>
</ul>
<p><strong>Room Control IO Configuration - Indication/Controls:</strong></p>
<p><strong><br /></strong>Select Mode Daikin Modbus RTD-RA</p>
<table>
<tbody>
<tr>
<th>Room Control function</th>
<th>Daikin</th>
</tr>
<tr>
<td>Setpoint</td>
<td>SET Setpoint</td>
</tr>
<tr>
<td>Operation state</td>
<td>SET Operation state</td>
</tr>
<tr>
<td>Fan level</td>
<td>SET Fan level</td>
</tr>
<tr>
<td>Fan direction</td>
<td>SET Fan direction</td>
</tr>
<tr>
<td>Mode</td>
<td>SET Mode</td>
</tr>
</tbody>
</table>
<p><strong>Room Control - Parameters:</strong></p>
<p>Increase the controller speed:</p>
<ul>
<li><strong>P gain:</strong> 25</li>
<li><strong>I gain:</strong> 5</li>
<li><strong>Integration time I:</strong> 300 s</li>
</ul>

Description (DE)

<p>Es können bis zu 32 Daikin-Geräte integriert werden.</p>
<p><strong>Device Station Einstellungen</strong></p>
<p>Geben Sie die <strong>Slave-IDs</strong> im Feld &bdquo;Slaves&ldquo; ein, getrennt durch ein Komma.</p>
<p>Beispiel: 1,2,3,4,...</p>
<p><strong>Funktionsbeschreibung</strong></p>
<p>Daikin Fan-Coil-Ger&auml;te arbeiten als Modbus-Slaves, w&auml;hrend der Controller als Modbus-Master arbeitet. Standardm&auml;&szlig;ig regelt der Controller die Raumtemperatur, indem er die L&uuml;fterstufe und den Ein-/Aus-Zustand an die einzelnen Fan-Coil-Ger&auml;te sendet.</p>
<p>Die gew&uuml;nschten Temperatursollwerte k&ouml;nnen direkt im System <strong>Raumregelung</strong> eingestellt werden. Die Heiz- und K&uuml;hlfunktion kann &uuml;ber konfigurierbare Aktionen/Timer umgeschaltet werden.</p>
<p>Die Daikin-Modi <strong>Auto</strong>, <strong>L&uuml;fter</strong> und <strong>Entfeuchtung</strong> k&ouml;nnen nicht gesteuert werden.</p>
<p><strong>Hinweis</strong></p>
<p>Die Fernbedienung kann verwendet werden, wenn einzelne R&auml;ume ausgeschaltet wurden. In diesem Fall sendet der Controller keine &Auml;nderungen der L&uuml;fterstufe an die Fan-Coil-Ger&auml;te.</p>
<p><strong>Anschluss</strong></p>
<p>Der Echtzeitkonverter wird in jedem Fan-Coil-Ger&auml;t installiert und &uuml;ber 3 Adern (A/B/GND) mit dem RS485-Bus verbunden. (z. B. FTDI: A&minus; = gelb, B+ = orange).</p>
<p>Um Modbus am Konverter zu aktivieren, muss &uuml;ber die DIPs 3 bis 8 einfach eine Adresse &gt;= 1 eingestellt werden. Die ersten beiden DIPs k&ouml;nnen deaktiviert bleiben, sofern kein Modbus-Timeout zur Aktivierung des lokalen Betriebs verwendet werden soll. In diesem Fall m&uuml;ssen die entsprechenden Register beschrieben werden.</p>
<p>Die Fan-Coil-Ger&auml;te sind zus&auml;tzlich separat mit dem Au&szlig;enger&auml;t verbunden. Der Heizbetrieb ist nur unterhalb der standardm&auml;&szlig;igen Au&szlig;entemperatur von 18 &deg;C m&ouml;glich.</p>
<p>Erstellen Sie f&uuml;r jedes Fan-Coil-Ger&auml;t ein Element <strong>Raumregelung</strong>.</p>
<p><strong>Raumregelung IO-Konfiguration &ndash; Sensoren:</strong></p>
<ul>
<li><strong>Temperatur:</strong> Geben Sie den Temperatursensor an.</li>
</ul>
<p><strong>Raumregelung IO-Konfiguration - Anzeige/Ansteuerungen:</strong></p>
<p><strong><br /></strong>Modus &bdquo;Daikin Modbus RTD-RA&ldquo; ausw&auml;hlen</p>
<table>
<tbody>
<tr>
<th>Raumregelungsfunktion</th>
<th>Daikin</th>
</tr>
<tr>
<td>Sollwert</td>
<td>SET Setpoint</td>
</tr>
<tr>
<td>Betriebsstatus</td>
<td>SET Operation state</td>
</tr>
<tr>
<td>L&uuml;fterstufe</td>
<td>SET Fan level</td>
</tr>
<tr>
<td>L&uuml;fterrichtung</td>
<td>SET Fan direction</td>
</tr>
<tr>
<td>Heizen/K&uuml;hlen</td>
<td>SET Mode</td>
</tr>
</tbody>
</table>
<p><strong>Raumregelung - Parameter:</strong></p>
<p>Regelgeschwindigkeit des Controllers erh&ouml;hen:</p>
<ul>
<li><strong>P-Verst&auml;rkung:</strong> 25</li>
<li><strong>I-Verst&auml;rkung:</strong> 5</li>
<li><strong>Integrationszeit I:</strong> 300 s</li>
</ul>

Description (IT)

<p>Integrare fino a 32 dispositivi Daikin.</p>
<p><strong>Impostazioni Device Station</strong></p>
<p>Inserire gli <strong>ID slave</strong> nel campo &bdquo;Slaves&ldquo;, separati da una virgola.</p>
<p>Esempio: 1,2,3,4,...</p>
<p><strong>Descrizione del funzionamento</strong></p>
<p>Le unit&agrave; fan coil Daikin funzionano come slave Modbus, mentre il controller opera come master Modbus. Per impostazione predefinita, il controller regola la temperatura ambiente inviando il livello della ventola e lo stato On/Off alle singole unit&agrave; fan coil.</p>
<p>Le temperature desiderate possono essere impostate direttamente nel sistema <strong>Regolazione ambiente</strong>. Il funzionamento in riscaldamento e raffrescamento pu&ograve; essere commutato tramite azioni/timer configurabili.</p>
<p>Le modalit&agrave; Daikin <strong>Auto</strong>, <strong>Ventilazione</strong> e <strong>Deumidificazione</strong> non possono essere controllate.</p>
<p><strong>Nota</strong></p>
<p>Il telecomando pu&ograve; essere utilizzato quando i singoli ambienti sono stati disattivati. In questo caso, il controller non invia modifiche del livello della ventola alle unit&agrave; fan coil.</p>
<p><strong>Collegamento</strong></p>
<p>Il convertitore real-time viene installato in ogni unit&agrave; fan coil e collegato al bus RS485 tramite 3 fili (A/B/GND). (ad es. FTDI: A&minus; = giallo, B+ = arancione).</p>
<p>Per abilitare Modbus sul convertitore, &egrave; sufficiente impostare un indirizzo &gt;= 1 tramite i DIP da 3 a 8. I primi 2 DIP possono rimanere disattivati, a meno che non si desideri utilizzare un timeout Modbus per abilitare il funzionamento locale. In questo caso, &egrave; necessario scrivere nei registri corrispondenti.</p>
<p>Le unit&agrave; fan coil sono inoltre collegate separatamente all'unit&agrave; esterna. Il funzionamento in riscaldamento &egrave; possibile solo al di sotto della temperatura esterna standard di 18 &deg;C.</p>
<p>Creare un elemento <strong>Regolazione ambiente</strong> per ogni unit&agrave; fan coil.</p>
<p><strong>Configurazione IO Regolazione ambiente &ndash; Sensori:</strong></p>
<ul>
<li><strong>Temperatura:</strong> Specificare il sensore di temperatura.</li>
</ul>
<p><strong>Configurazione IO Regolazione ambiente - Mostra/Controlli:</strong></p>
<p><strong><br /></strong>Selezionare la modalit&agrave; &bdquo;Daikin Modbus RTD-RA&ldquo;</p>
<table>
<tbody>
<tr>
<th>Funzione Regolazione ambiente</th>
<th>Daikin</th>
</tr>
<tr>
<td>Setpoint</td>
<td>SET Setpoint</td>
</tr>
<tr>
<td>Stato di funzione</td>
<td>SET Operation state</td>
</tr>
<tr>
<td>Livello ventilatore</td>
<td>SET Fan level</td>
</tr>
<tr>
<td>Direzione del ventilatore</td>
<td>SET Fan direction</td>
</tr>
<tr>
<td>Riscaldamento/raffreddamento</td>
<td>SET Mode</td>
</tr>
</tbody>
</table>
<p><strong>Regolazione ambiente - Parametri:</strong></p>
<p>Aumentare la velocit&agrave; di regolazione del controller:</p>
<ul>
<li><strong>Guadagno P:</strong> 25</li>
<li><strong>Guadagno I:</strong> 5</li>
<li><strong>Tempo di integrazione I:</strong> 300 s</li>
</ul>

Note

from

*2026-10-08 07:02:29 (do) ******************************
Last Commit: 0fc66f39 | 2026-10-05 15:49:33

Downloads sind nur für aktive Benutzer (active > 0) verfügbar.

Device images stehen nur für aktive Benutzer (active > 0) zur Verfügung.

Der Zugriff auf DDF-Dateien ist nur für aktive Benutzer (active > 0) möglich.

INDEX	ALIAS	NAME	UNIT
1	SETPOINT	Setpoint	C (10 to 31)
2	FAN_LEVEL	Fan level	0 = Automatic, 1 to 5
3	MODE	Mode	0 = Auto, 1 = Heat, 2 = Fan, 3 = Cool, 4 = Dry
4	FAN_DIRECTION	Fan direction	0 = Stop, 1 = Swing
5	OPERATION_STATE	Operation state	0 = Off, 1 = On
101	SET_SETPOINT	SET Setpoint	C (10 to 31)
102	SET_FAN_LEVEL	SET Fan level	0 = Automatic, 1 to 5
103	SET_MODE	SET Mode	0 = Auto, 1 = Heat, 2 = Fan, 3 = Cool, 4 = Dry
104	SET_FAN_DIRECTION	SET Fan direction	0 = Stop, 1 = Swing
105	SET_OPERATION_STATE	SET Operation state	0 = Off, 1 = On
200	QUALITY	Quality	1 = OK

General Parameters

Description (HTML)

Description (DE)

Description (IT)

Note

Documents

Device Description File